TCXO TG-5006CJ
Product name TG-5006CJ-27L 38.400000 MHz
Product Number / Ordering code X1G0041310018xx
Please refer to the 10.Packing information about xx (last 2 digits)
Output waveform Clipped sine wave
Pb free / Complies with EU RoHS directive
Reference weight Typ.9.1mg
1.Absolute maximum ratings
Parameter Symbol Min. Typ. Max. Unit Conditions / Remarks
V
CC
-GND
-0.3 - 4 V Vcc terminal
T_stg -40 - 90 ºC Storage as single product
Parameter Symbol Min. Typ. Max. Unit Conditions / Remarks
Supply voltage
Vcc 1.7 - 3.3 V
GND = 0V
- -
-
Operating temperature
T_use -30 25 85 ºC
-
Output load condition
Load_R 9 10 11 kΩ
-
Load_C 9 10 11 pF
DC cut capacitor=0.01µF
DC-cut capacitor is not included in this TCXO. Please attach an external DC-cut capacitor (0.01 μF Min.) to the out pin.
(Vcc=1.8, 2.8, 3.0, 3.3 V, Vc=1.65 V, GND=0.0 V, Load 10 kΩ//10 pF(DC cut), T_use=+25ºC)
3.Frequency Characteristics
Parameter Symbol Min. Typ. Max. Unit Conditions / Remarks
Output frequency
f0 - 38.4000 - MHz
Frequency tolerance
f_tol -2.0 - 2.0
x10
-6
T_use = +25ºC, Reflow 2 times
x10
-6
T_use = -30 ºC to +85 ºC
temperature characteristics
- - -
-
Frequency / load coefficient
f0-Load -0.2 - 0.2
x10
-6
10 kΩ // 10 pF +/- 10%
Frequency / voltage coefficient
f0-Vcc -0.2 - 0.2
- - -
-
- - -
-
Frequency aging
f_age -1.0 - 1.0
x10
-6
1st year, T_use=25degC
*1 Include initial frequency tolerance and frequency deviation after reflow cycles.
*2 Measured in the elapse of 24 hours after reflow soldering.
*3 Vcc +/- 5% must be in operating supply voltage range (1.7 V to 3.47 V)
(Vcc=1.8, 2.8, 3.0, 3.3 V, Vc=1.65 V, GND=0.0 V, Load 10 kΩ//10 pF(DC cut), T_use=+25ºC)
4.Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Conditions / Remarks
Current consumption
Icc - - 2 mA
T_Use = +25ºC , 10 kΩ//10pF
Symmetry
SYM 40 - 60 %
GND Level
Output voltage
Vp-p 0.8 - 1.5 V
Peak to peak 10 kΩ//10pF +/- 10%
Harmonics
- - - -8
start up time
tosc - - 2.0 ms
Within 90% of final amp.
- - 2.0 ms
ΔF = +/- 1.0 x 10-6
Phase noise
L(f) - - -82
- - -148 dBc/Hz
Offset:1 MHz
Output waveform (Clipped sine wave output)
1) Output Load : 10 kΩ//10 pF
2) Current consumption
3) Conditions
1. Oscilloscope: Impedance Min. 1 MΩ
Input capacitance Max. 10 pF
Band width Min. 300 MHz
Impossible to measure both frequency and wave form at the same time.(In case of using
oscilloscope's amplifier output, possible to measure both at the same time.)
2. Load_C includes probe capacitance.
3. A capacitor (By-pass:0.01 to 0.1 uF) is placed between V
CC
and GND,and closely to TCXO.
4. Use the current meter whose internal impedance value is small.
5. Power Supply
Impedance of power supply should be as low as possible.
7.External dimensions (Unit: mm) 8.Footprint(Recommended) (Unit: mm)
[ 1 ]Product number last 2 digits code(xx) description The recommended code is "00"
Code Code
00 12000pcs / Reel 14 1000pcs / Reel
01 Any Q'ty vinyl bag(Tape cut) 15 2000pcs / Reel
11 Any Q'ty / Reel 16 3000pcs / Reel
To maintain stable operation, provide a 0.01uF to 0.1uF
by-pass capacitor at a location as near as possible to the
power source terminal of the crystal product (between Vcc
ts
60sto180s
(+150Cto+200C)
Avg. Ramp-up
3
C/sMax.
Ramp-down
6C/sMax.
tL
60sto150s
(+217Cover)
